EZYPOR® Liquid Measure
EZYPOR® Liquid Measure
Perfect measuring device, allows safe and easy dispensing. Fits any plastic bottle with a 28 millimeter cap thread. (soda bottle) $9.95
EZYPOR - precise measure, accurate, no leaks, no drips
Great addition to FTC Decarbonizer and Marine Diesel Stabilizer 16 fl oz bottles. Adds a perfect measuring device to these bottles, and allows safe and easy dispensing! So easy to use! Accurate measuring! No mess dispensing!
-
Child-proof caps!
-
Fully sealed - stays on the bottle till empty!
-
Excess drips go back into the bottle!
-
Measures in 5 mL increments up to 20 mL!
-
Re-usable - only buy it once for each product!
You only need to purchase EZYPOR once. It simply screws on and replaces the original bottle cap, and it seals just as the original cap would. The caps are child proof - both where it screws onto the bottle, and also on its own cap. Fit the EZYPOR device, and gently squeeze the bottle which fills up the clear plastic chamber in 5 mL increments up to 20 mL, allowing for a precise measure.
Once you remove the EZYPOR cap, a spring-loaded spout protrudes a little from the device. A non-return valve prevents the liquid returning to the bottle as you up-end the bottle to dispense the additive. This allows you to only dispense the amount of additive you've chosen, and no more. A very simple and easy-to-use device; no leaks, no drips, no dirty hands, no smells. An easy, convenient, and accurate measure for FTC Decarbonizer and Marine Diesel Stabilizer 16 fl oz bottles. - 1"
SET UP
Measure and cut the pick-up tube to the correct length for the bottle you are attaching the EZYPOR to. It's best to make the tube just marginally longer (0.5"/13 mm) so that it extends completely to the bottom of the bottle - this ensures you can get the very last drops from the bottle as it empties.
HOW TO USE
Ensure the top cap of the EZYPOR is fitted securely. Remove the existing bottle cap and screw the EZYPOR on the bottle. Make sure it is on tightly - it has a child-proof cap system and will turn freely once it is tightened enough. To test for leaks, ensure the top cap is screwed on, and gently squeeze the bottle. If no air can be heard escaping, it's good to go.
Remove the top child-proof cap. The extension nozzle pops up to enable easy pouring into small openings.
Gently squeeze the bottle. The liquid in the bottle moves up the tube and starts to fill the reservoir. Stop squeezing when the correct level is reached (max of 20 mL per measure). The reservoir is marked in 5 mL increments to a maximum of 20 mL on one side and ½ fl oz measure on the other side.
Invert the bottle and pour out the liquid. A valve inside the EZYPOR prevents any more liquid from coming out of the bottle while it is inverted. This ensures an accurate measure.
When you return the bottle to upright, any drips get trapped by the pop-up nozzle. When the cap is replaced, the nozzle pushes down and returns the drip to the reservoir.
Replace the child-proof cap, pressing down firmly to start as the spring-loaded extension nozzle will resist a little. Now you’re finished - clean hands, no smell, and the right amount! Keep the EZYPOR on the bottle. It is sealed and is designed to stay on the bottle. When your product runs out, you can re-use it for the next one!
Perfect for many other applications - mixing 2-stroke engine oils, herbicides, cleaning agents, household chemicals etc! Purchase it separately, or add to shopping cart when buying our products!
* Note - If the bottle does not have a thread length of at least 1/2" (13 millimeters), a leak can occur. In the picture, the bottle on the right hand side lacks adequate thread length and could possibly leak. To remedy this, it is recommended to use the supplied washer - place the washer inside the EZYPOR threaded section until it is snug against the bottom flat surface. Screw the EZYPOR tightly on to the bottle, and test again for air escaping as described above. Tighten as necessary.
Ensure the EZYPOR reservoir is empty and the bottle is in an upright position when storing. Where possible, especially if using with FTC Decarbonizer or Marine Diesel Stabilizer, avoid storing in direct sunlight and/or any areas with high temperature exposure as pressure in the bottle may increase, forcing pressurized liquid into the EZYPOR chamber.
If storing these products in a vehicle with the EZYPOR affixed, it is strongly recommended to store inside a sturdy, sealable plastic bag or other spill-proof container.
If the EZYPOR reservoir self-fills due to high temperature and/or atmospheric pressure (altitude) changes, hold the bottle upright and slowly and carefully loosen the main, lower cap of the EZYPOR from the bottle just a little. This will allow pressure inside the bottle to be released. It is recommended to wear gloves while releasing the pressure to avoid contact with skin. Exercise caution. Do not loosen the EZYPOR top cap to relieve pressure, as pressurized fluid loss will occur and staining may result. Once the pressure has released, retighten the main cap. Note: fluid in the reservoir will not return to the bottle during this procedure.
It is important to not swap your EZYPOR from one product bottle to a different product bottle; for example, FTC Decarbonizer and herbicides etc. The cross contamination from product to product can have an unintended harmful effect on the components the product comes in contact with. We strongly recommend having one EZYPOR for each individual product and just swapping to the replacement product bottle when needed.
Disclosure: Combining chemicals can be dangerous! It is NOT RECOMMENDED to use the same EZYPOR to dispense different chemicals. Chemical resistance is based on the use of common domestic liquids and fuel additives. Although industrial chemicals may be used with EZYPOR, no guarantee is offered, and they must be tested before use.
Disclaimer - By purchasing the product, the purchaser agrees that neither Maxodyne LLC, Pro Maintenance Additives LLC, nor EZYPOR (NZ) Ltd. can be held responsible or liable for any possible resulting loss, harm, injury or damage to anyone or anything, as these entities have no control over the actions of the purchaser or user concerning the product
